virgomoney37

How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners have a unique procedure to add another key. It requires dealer support using a handheld computer dubbed Tech-2. Then it is necessary to purchase a new transponder. key must be purchased. Change your keys regularly to prevent one from wearing out faster than another. This will also keep your keys in top shape. Replacement Case The new key fobs do not look like the older Saab keys. They feature electronic components which make it hard to duplicate. This has made stealing car keys much more difficult than it was twenty years ago. It has also made it more expensive to replace keys lost. Saab 9-3 owners should have two keys working. It is expensive to replace a lost key because it requires replacing the CIM module, and reconfiguring the locking cylinders. Dealers usually charge between $100 and $200 to complete this. There are options to avoid these high costs. saab 93 key fob will use the code of a spare key to cut a brand new metal blade at a fraction that of a dealer. The key, however, must be the same as the original to work correctly within your car. Follow these steps to replace the case. You will need to have an open-faced screwdriver and patience. With the screwdriver slowly break the plastic and then separate the emergency key from the case. When the case is opened remove all electronics and put them back in the new case. Be sure to put the correct badge and key back into the case as well. Replacement Battery The Saab 9-3 replacement battery is a cheap part that can be easily and quickly replaced. This YouTube video by Cyclone Cyd shows how to replace the battery for the remote fob in just four simple steps. This tutorial is suitable for any modern saab key fob however the procedure might differ slightly. The button is normally located close to the Saab logo on the back of the fob. It's usually near the Saab logo on the back of the fob. Use a flathead screwdriver to insert the screwdriver in the small hole in this button. This will be enough to allow you to open the fob's case to allow you to replace the battery. After you have installed the new batteries CR1632, you can reassemble your remote key fob. Then, you can program it into your car. The procedure should take no more than an hour at most. It's a very easy procedure that doesn't require any special equipment. The process is a bit more complicated in the event that you lose your key, but still possible. The dealer needs to first determine the VIN of the vehicle, and then purchase the replacement TWICE module as well as key blade with the proper unique code. The dealer will then need to program the key using MDI, a new software tool. Key Replacement Fob The key fob is equipped with batteries that are used to lock and unlock your vehicle. They have a limited life span and eventually will die. This is a problem that occurs that affects all cars. The good thing is that you can change the batteries in most key fobs, and not have to replace the entire case. Amazon sells replacement fobs that already have all the electronics in place. It is easy to pop the case open and replace the batteries. It is important to note that you'll need to take out the emergency key first, and you can do this by putting a small flathead screwdriver into the slot that is located in the middle of the case. Use the screwdriver to move around the case, and it will split open, making it simple to take it out. When you are ready to replace the keys, make sure you have a spare because this can cut down the total cost by a substantial amount. If you have an additional key, you can ask the dealer to cut it in half and program it to your car. This is much cheaper than purchasing a new fob. If you do not have a spare key one, you can add another key to your car, but it requires a lot of research and effort. The cost for adding a second key is several hundred dollars and also requires programming of the car's computer. This can be accomplished by a professional, however it's an expensive option for most owners. Replacement Ignition In contrast to the earlier Saab automobiles, the new SAAB 9-3 models have an extremely sophisticated alarm system that is based on a coded key. This means that should you lose only one working key, replacing it with an additional one could be extremely expensive because the car needs to have a specific computer module added and it also needs to be specifically programmed to accept an extra key. The majority of locksmiths aren't able to do this or even a dealer will charge several hundred dollars to program the new key! If you've lost your only working key the dealer will replace your car's computer (known as the CIM or SAAB TWICE) in order to make a replacement, and they will charge top dollar for it. Instead, we can reprogram the EEPROM of your current car computer to allow it to be programmed for a replacement key, and save you over 50% of the amount you be charged at a dealership. If you've been a faithful owner of a 03-11 SAAB 9-3, then you likely know that the ignition key isn't the most robust. If your ignition key isn't functioning properly, it is time to consider replacing it. They can become sticky and the buttons have been known to fall off. It's good to know that replacing the ignition key isn't as difficult as it seems and is fairly easy to do using the right tools.